(散件) 8路 八路抢答器DIY制作套件CD4511多路散件电子实训器材
Link to the original- 100 — 1999 шт 5000$ per piece.
- 2000 — 50119 шт 4000$ per piece.
- 50120+ шт 3000$ per piece.
Inspection + photo report for $1.5.
We check the goods and take a photo report so you can make sure you get the right product without faults or damage
Delivery from China to Ukraine, Uzbekistan, European and African countries
Payable upon arrival at the warehouse in China
Returns are only possible while the item is in our warehouse in China. Once the goods have been dispatched from China, they cannot be returned
Photo and product description
参数:
供电电压:4.5-5.5V
按键功能:NO.1到NO.8为选手,REST为主持人
尺寸:6.7厘米*6.1厘米
功能介绍:
套件有9个按键,8个抢答编号,1个抢答复位,上电后,数码管显示0,开始进行抢答,8个按键中哪一个按键zui先被按下,数码管马上显示zui先被按下按键的编号,并锁定显示,表示抢答成功,其他按键再按下已经失效,只有按下复位按键,数码管清0,才可进行新一轮的抢答,按键按下伴有蜂鸣器的响声。
常见问题:
1.电阻注意区分阻值焊接,电阻阻值要跟板子上一一对应。
2.二极管1N4148注意区分正负极,有黑色的一边对应板子上有横杠的一边,既是负极端。
3.电解电容长管脚是正极,蜂鸣器也是长管脚正极。
4.芯片缺口方向和底座缺口方向要跟板子上标识的缺口方向一致。
5.数码管注意方向,小数点在下。
6.供电注意正负极,VCC接正极,GND接负极,直流电压4.5-5.5V。
7.注意检查焊接短路和虚焊的现象。
焊接制作视频:http://v.qq.com/x/page/q08088s782y.html
资料链接:https://pan.baidu.com/s/14KWJkm7Q_26qzaweqXEH2w 提取码:a1b2
提供资料:
电路板空板正面图片:
电路板空板背面图片:
原理图:
电路原理:电路包括抢答,编码,优先,锁存,数显及复位电路。可同时进行八路优先抢答,按键按下后,蜂鸣器发声,同时数码管显示优先抢答者的号数,抢答成功后,再按按键,显示不会改变,除非按复位键。复位后,显示清零,可继续抢答。S1-S8为抢答键,S9为复位键。CD4511是一块含BCD-7段锁存/译码/驱动电路于一体的集成电路,其中1、2、6、7为BCD码输入端,9~15脚为显示输出端,3脚(LT)为测试输出端,当“LT”为0时,输出全为1,4脚(BI)为消隐端,BI为0时输出全为0,5脚(LE)为锁存允许端,当LE由“0”变为“1”时,输出端保持LE为0时的显示状态。
套件清单:(也就是发货清单)
注意事项:
1.注意板子上的元件从体积小的开始焊接,然后再焊接大的。
2.个别元件如电阻电容等暂时缺货,我们会发其符号电路原理的他附近值的元件代替,蓝色的金属膜电阻的可能换成灰色的碳膜电阻发,灰色的碳膜电阻的也可能换成蓝色的金属膜电阻来发。是一样的效果。
3.焊接好后,请自助调试,焊接没出错的话一般都可以成功,如果焊接失败,本店只能协助您查看问题所在,我们不能保证您一焊接就能成功,这个也是为什么工厂生产线上需要维修工的原因,电子产品因为静电击穿,因为电源正负极接错烧坏,因为虚焊,因为元件焊接错位置等等等等原因出现问题的几率很大,别总说板子线路是有问题的,这个板子卖了几万人,出问题的就几十个人!我们尽力做到良好的售后服务,尽力协助各位朋友完成制作。因此,当遇到制作出来的成品没有达到我们所描述的效果时,请先不要急于给我们评价,记得联系我们的售后服务,我们会竭尽全力。谢谢合作,祝大家购物愉快!